trim the config
This commit is contained in:
Jakob Ketterl
parent
d5f17d66d9
commit
de84dc71e8
@ -36,7 +36,6 @@ config_webrx: configuration options for OpenWebRX
|
||||
|
||||
# ==== Server settings ====
|
||||
web_port=8073
|
||||
server_hostname="localhost" # If this contains an incorrect value, the web UI may freeze on load (it can't open websocket)
|
||||
max_clients=20
|
||||
|
||||
# ==== Web GUI configuration ====
|
||||
@ -65,6 +64,7 @@ Website: <a href="http://localhost" target="_blank">http://localhost</a>
|
||||
sdrhu_key = ""
|
||||
# 3. Set this setting to True to enable listing:
|
||||
sdrhu_public_listing = False
|
||||
server_hostname="localhost"
|
||||
|
||||
# ==== DSP/RX settings ====
|
||||
fft_fps=9
|
||||
@ -77,8 +77,6 @@ fft_compression="adpcm" #valid values: "adpcm", "none"
|
||||
digimodes_enable=True #Decoding digimodes come with higher CPU usage.
|
||||
digimodes_fft_size=1024
|
||||
|
||||
start_rtl_thread=True
|
||||
|
||||
"""
|
||||
Note: if you experience audio underruns while CPU usage is 100%, you can:
|
||||
- decrease `samp_rate`,
|
||||
@ -95,16 +93,16 @@ Note: if you experience audio underruns while CPU usage is 100%, you can:
|
||||
# Check here: https://github.com/simonyiszk/openwebrx/wiki#guides-for-receiver-hardware-support #
|
||||
#################################################################################################
|
||||
|
||||
# You can use other SDR hardware as well, by giving your own command that outputs the I/Q samples... Some examples of configuration are available here (default is RTL-SDR):
|
||||
|
||||
# valid: "rtl_sdr", "sdrplay", "hackrf"
|
||||
#rtl_type = "sdrplay"
|
||||
# Currently supported types of sdr receivers: "rtl_sdr", "sdrplay", "hackrf"
|
||||
|
||||
sdrs = {
|
||||
"rtlsdr": {
|
||||
"name": "RTL-SDR USB Stick",
|
||||
"type": "rtl_sdr",
|
||||
"ppm": 0,
|
||||
# you can change this if you use an upconverter. formula is:
|
||||
# shown_center_freq = center_freq + lfo_offset
|
||||
# "lfo_offset": 0,
|
||||
"profiles": {
|
||||
"70cm": {
|
||||
"name": "70cm Relais",
|
||||
@ -163,68 +161,14 @@ sdrs = {
|
||||
}
|
||||
}
|
||||
},
|
||||
# this one is just here to test feature detection
|
||||
"test": {
|
||||
"type": "test"
|
||||
}
|
||||
}
|
||||
|
||||
# >> RTL-SDR via rtl_sdr
|
||||
#start_rtl_command="rtl_sdr -s {samp_rate} -f {center_freq} -p {ppm} -g {rf_gain} -".format(rf_gain=rf_gain, center_freq=center_freq, samp_rate=samp_rate, ppm=ppm)
|
||||
#format_conversion="csdr convert_u8_f"
|
||||
|
||||
#lna_gain=8
|
||||
#rf_amp=1
|
||||
#start_rtl_command="hackrf_transfer -s {samp_rate} -f {center_freq} -g {rf_gain} -l{lna_gain} -a{rf_amp} -r-".format(rf_gain=rf_gain, center_freq=center_freq, samp_rate=samp_rate, ppm=ppm, rf_amp=rf_amp, lna_gain=lna_gain)
|
||||
#format_conversion="csdr convert_s8_f"
|
||||
"""
|
||||
To use a HackRF, compile the HackRF host tools from its "stdout" branch:
|
||||
git clone https://github.com/mossmann/hackrf/
|
||||
cd hackrf
|
||||
git fetch
|
||||
git checkout origin/stdout
|
||||
cd host
|
||||
mkdir build
|
||||
cd build
|
||||
cmake .. -DINSTALL_UDEV_RULES=ON
|
||||
make
|
||||
sudo make install
|
||||
"""
|
||||
|
||||
# >> Sound card SDR (needs ALSA)
|
||||
# I did not have the chance to properly test it.
|
||||
#samp_rate = 96000
|
||||
#start_rtl_command="arecord -f S16_LE -r {samp_rate} -c2 -".format(samp_rate=samp_rate)
|
||||
#format_conversion="csdr convert_s16_f | csdr gain_ff 30"
|
||||
|
||||
# >> /dev/urandom test signal source
|
||||
# samp_rate = 2400000
|
||||
# start_rtl_command="cat /dev/urandom | (pv -qL `python -c 'print int({samp_rate} * 2.2)'` 2>&1)".format(rf_gain=rf_gain, center_freq=center_freq, samp_rate=samp_rate)
|
||||
# format_conversion="csdr convert_u8_f"
|
||||
|
||||
# >> Pre-recorded raw I/Q file as signal source
|
||||
# You will have to correctly specify: samp_rate, center_freq, format_conversion in order to correctly play an I/Q file.
|
||||
#start_rtl_command="(while true; do cat my_iq_file.raw; done) | csdr flowcontrol {sr} 20 ".format(sr=samp_rate*2*1.05)
|
||||
#format_conversion="csdr convert_u8_f"
|
||||
|
||||
#>> The rx_sdr command works with a variety of SDR harware: RTL-SDR, HackRF, SDRplay, UHD, Airspy, Red Pitaya, audio devices, etc.
|
||||
# It will auto-detect your SDR hardware if the following tools are installed:
|
||||
# * the vendor provided driver and library,
|
||||
# * the vendor-specific SoapySDR wrapper library,
|
||||
# * and SoapySDR itself.
|
||||
# Check out this article on the OpenWebRX Wiki: https://github.com/simonyiszk/openwebrx/wiki/Using-rx_tools-with-OpenWebRX/
|
||||
#start_rtl_command="rx_sdr -F CF32 -s {samp_rate} -f {center_freq} -p {ppm} -g {rf_gain} -".format(rf_gain=rf_gain, center_freq=center_freq, samp_rate=samp_rate, ppm=ppm)
|
||||
#format_conversion=""
|
||||
|
||||
# >> gr-osmosdr signal source using GNU Radio (follow this guide: https://github.com/simonyiszk/openwebrx/wiki/Using-GrOsmoSDR-as-signal-source)
|
||||
#start_rtl_command="cat /tmp/osmocom_fifo"
|
||||
#format_conversion=""
|
||||
|
||||
# ==== Misc settings ====
|
||||
|
||||
# you can change this if you use an upconverter. formula is:
|
||||
# shown_center_freq = center_freq + lfo_offset
|
||||
lfo_offset = 0
|
||||
|
||||
client_audio_buffer_size = 5
|
||||
#increasing client_audio_buffer_size will:
|
||||
# - also increase the latency
|
||||
@ -232,8 +176,6 @@ client_audio_buffer_size = 5
|
||||
|
||||
iq_port_range = [4950, 4960] #TCP port for range ncat to listen on. It will send I/Q data over its connections, for internal use in OpenWebRX. It is only accessible from the localhost by default.
|
||||
|
||||
#access_log = "~/openwebrx_access.log"
|
||||
|
||||
# ==== Color themes ====
|
||||
|
||||
#A guide is available to help you set these values: https://github.com/simonyiszk/openwebrx/wiki/Calibrating-waterfall-display-levels
|
||||
@ -270,11 +212,3 @@ csdr_print_bufsizes = False # This prints the buffer sizes used for csdr proces
|
||||
csdr_through = False # Setting this True will print out how much data is going into the DSP chains.
|
||||
|
||||
nmux_memory = 50 #in megabytes. This sets the approximate size of the circular buffer used by nmux.
|
||||
|
||||
#Look up external IP address automatically from icanhazip.com, and use it as [server_hostname]
|
||||
"""
|
||||
print "[openwebrx-config] Detecting external IP address..."
|
||||
import urllib2
|
||||
server_hostname=urllib2.urlopen("http://icanhazip.com").read()[:-1]
|
||||
print "[openwebrx-config] External IP address detected:", server_hostname
|
||||
"""
|
||||
|
||||
14
openwebrx.py
14
openwebrx.py
@ -13,12 +13,14 @@ class ThreadedHttpServer(ThreadingMixIn, HTTPServer):
|
||||
|
||||
|
||||
def main():
|
||||
print()
|
||||
print("OpenWebRX - Open Source SDR Web App for Everyone! | for license see LICENSE file in the package")
|
||||
print("_________________________________________________________________________________________________")
|
||||
print()
|
||||
print("Author contact info: Andras Retzler, HA7ILM <randras@sdr.hu>")
|
||||
print()
|
||||
print("""
|
||||
|
||||
OpenWebRX - Open Source SDR Web App for Everyone! | for license see LICENSE file in the package
|
||||
_________________________________________________________________________________________________
|
||||
|
||||
Author contact info: Andras Retzler, HA7ILM <randras@sdr.hu>
|
||||
|
||||
""")
|
||||
|
||||
cfg = __import__("config_webrx")
|
||||
pm = PropertyManager.getSharedInstance()
|
||||
|
||||
@ -131,6 +131,19 @@ class FeatureDetector(object):
|
||||
def has_rx_tools(self):
|
||||
return os.system("rx_sdr --help 2> /dev/null") != 32512
|
||||
|
||||
"""
|
||||
To use a HackRF, compile the HackRF host tools from its "stdout" branch:
|
||||
git clone https://github.com/mossmann/hackrf/
|
||||
cd hackrf
|
||||
git fetch
|
||||
git checkout origin/stdout
|
||||
cd host
|
||||
mkdir build
|
||||
cd build
|
||||
cmake .. -DINSTALL_UDEV_RULES=ON
|
||||
make
|
||||
sudo make install
|
||||
"""
|
||||
def has_hackrf_transfer(self):
|
||||
# TODO i don't have a hackrf, so somebody doublecheck this.
|
||||
# TODO also check if it has the stdout feature
|
||||
|
||||
Loading…
Reference in New Issue
Block a user